My universal methods for achieving a better gaming experience on Windows handheld with the lowest energy consumption

AMD Algorithm Priority (Not Recommended)

  1. Install AMD Software Adrenalin Edition
  2. Enable HYPR-RX (a series of optimizations)
  3. Lower the game resolution from 1920×1080 to 1280×720, 1366×768, or 1600×900
  4. Ensure Radeon Super Resolution is enabled (upscaling/resolution)
  5. Ensure AMD Fluid Motion Frames is enabled (frame interpolation)
  6. Lower the TDP to achieve 60fps through frame interpolation; further reduce for non-action games

The above steps aim to run games at low frame rates, low resolution, and low TDP, and then use AMD technologies applicable to all games for frame interpolation and upscaling/resolution to achieve a minimum TDP operation of 1080p 60fps. The image quality will be worse than native 1080p 60fps, but it can improve battery life by about 20-40%.

Power Saving Priority

  1. Install AMD Software Adrenalin Edition
  2. Turn off CPU Turbo Boost
  3. Remove frame rate limits in games and other management software
  4. Enable custom mode
  5. Enable Radeon Chill
  6. Set the minimum FPS to 30 and the maximum FPS to 45-60
  7. Enable Radeon Image Sharpening (optional, adds filter to sharpen object edges)

The above steps use Radeon Chill to dynamically lock the frame rate, adjusting to the maximum FPS during intense action and to the minimum FPS when there is no action to save power. Radeon Super Resolution and Fluid Motion Frames cannot be enabled simultaneously with Radeon Chill. Additionally, the low-power Radeon Image Sharpening filter can be used to sharpen object edges and make the image look clearer.

Lossless Scaling Algorithm with Power Saving (Recommended)

  1. Install AMD Software Adrenalin Edition.
  2. Disable CPU Turbo Boost.
  3. Remove frame rate limits in the game and other management software.
  4. Enable custom mode.
  5. Enable Radeon Chill.
  6. Set minimum FPS to 30 and maximum FPS to 45-60.
  7. Install Lossless Scaling.
  8. Set the game to 1280×720 windowed mode.
  9. Enable Scaling Type.
  10. Enable Frame Generation.

The above steps use the Lossless Scaling software to replace Radeon Super Resolution and Fluid Motion Frames. It enables Radeon Chill and simultaneously uses the superior Lossless Scaling algorithm for frame interpolation and upscaling /resolution. This achieves a better gaming experience and battery life compared to the AMD Algorithm, making it the recommended choice for users.



  1. 安裝AMD Software Adrenalin Edition
  2. 開啟HYPR-RX(一系列優化)
  3. 將遊戲解析度從1920×1080調降至1280×720、1366×768或1600×900
  4. 確認Radeon Super Resolution已啟用(升頻/解析度)
  5. 確認AMD Fluid Motion Frames已啟用(補幀數)
  6. 將TDP調降至透過補幀可達60fps,非動作遊戲可進一步調降

上述是在遊戲不支持原生FidelityFX Super Resolution(FSR)的情況下,以低幀數、低解析度和低TDP運行,再透過適用所有遊戲的AMD技術來補幀和升頻(解析度),以達成最低TDP運行1080p 60fps之方法,畫質會比原生1080p 60fps差,但可提升20-40%左右的續航力。


  • 安裝AMD Software Adrenalin Edition
  • 關閉CPU睿頻
  • 在遊戲和其他管理軟體解除幀數限制
  • 開啟自訂模式
  • 啟用Radeon Chill
  • 設置最小FPS 30,最大FPS 45-60
  • 開啟Radeon Image Shapening(加濾鏡銳化物體邊緣,可選)

上述是利用Radeon Chill動態鎖幀,在激烈動作時調整至最大FPS,在沒有動作時調整至最小FPS,用最少的電力換取更好的體驗(Radeon Super Resolution及Fluid Motion Frames不可與Radeon Chill同時啟用)。還可加上低功耗的Radeon Image Shapening濾鏡銳化物體邊緣,讓畫面看起來更清晰。

Lossless Scaling算法與省電(推薦)

  • 安裝AMD Software Adrenalin Edition
  • 關閉CPU睿頻
  • 在遊戲和其他管理軟體解除幀數限制
  • 開啟自訂模式
  • 啟用Radeon Chill
  • 設置最小FPS 30,最大FPS 45-60
  • 安裝Lossless Scaling
  • 將遊戲設置為1280×720視窗模式
  • 啟用Scaling Type
  • 啟用Frame Generation

上述是以Lossless Scaling軟體取代Radeon Super Resolution及Fluid Motion Frames,啟用Radeon Chill同時使用更好的Lossless Scaling算法補幀和升頻(解析度),可達成比AMD算法更好的遊戲體驗與續航力,推薦網友優先採用。